Do you want to learn how to plumb an above-ground pool? If so, this article is for you. We’ll go over the different steps involved in the installation of your above-ground pool plumbing system.

You’ll also find information on what tools are needed, as well as the best practices for installing your own plumbing.

How to Plumb an Above-Ground Pool

Here are the steps to plumb an above ground pool:

Step One: Prepare Your Tools

You need to prepare the tools you need before you can begin, such as:

• A plunger
• A wire coat hanger
• Plumbers tape
• A pipe wrench

Step Two: Shut Off Your Pool Water Supply Line and the Pipes to your House or Yard

This should be fairly self-explanatory. You need to make sure that there is no water in the pool at all before you start to work on it. If you don’t, any mistake can lead to a flood of epic proportions – literally!

The only thing worse than having an above-ground pool filled with ants would be one filled with actual ant water.  You also want to turn off your main supply line into the house and anything else leading outside of the house so that nobody gets their hands wet when they are filling up buckets of water to use for a shower, etc.

Step Three: Open the Drain on Your Pool and Attach a Garden Hose to it

You’re going to want some extra elbow room in case your pool is filled with more than you anticipated. Make sure that there aren’t any children or pets around before opening up anything! You can attach your hose from Step One here so that when you are finished, all of the water will drain away easily.

This part might take a while depending on how big your above-ground pool is, so be patient. You don’t want things getting drowned out, now do you?  It’s better just draining it into your yard if need be, although this means being careful about where exactly the water flows; otherwise, you might have some damp spots in your yard.

Step Four: Verify What You Need for Your Plumbing System

You should know what kind of plumbing system you need before you begin to work on it, so make sure that whatever it is meets local building codes and regulations first. If all the other information seems good but this one piece doesn’t look right, stop now, or else things will get worse later down the road if they aren’t already!

Step Five: Cut Your Pipes

This is the part where you need to start getting creative. You can use your saws-all or whatever else if this seems too difficult for what it’s worth, but every pool should have two main pipes coming in and out of it – one big one that’s usually about four inches wide, which brings water into the pool itself and a smaller pipe (two inches typically) leading from an overflow drain.

These are going to be exposed outside of your above-ground pool, so make sure they’re not directly under anything at all like flowerbeds, sidewalks, etc! It might also help to put some boards down ahead of time just in case any debris gets kicked up accidentally; nobody wants dirt clogging their beautiful new plumbing system now do they?

Step Six: Add Plumbers Tape to Your Main Water Pipe

This is an easy step since it’s just like when you’re adding a new faucet or showerhead.  Ensure there are no leaks and then proceed into the next part, which will attach your pool plumbing system this time around!

You want to make sure that everything is nice and snug, so don’t skimp out on any of these steps because otherwise, things can get messy in a hurry if they happen to slip off of something somewhere.

Step Seven: Attach Your Pipes Together Depending on How They Fit Over Top One Another

Again, this might take some creative engineering depending on how your above-ground pool was set up initially but try sticking with one type of fitting throughout the entire plumbing system.

For example, if you have a T and Y fitting at first then try to use those the whole way through so that your pipes always match up with one another nicely and nothing slips off of anything else by mistake.

Step Eight: Attach Everything Else You Need

This includes check valves, air relief valves (if necessary), vacuum breaker fittings, and any other accessories depending on what it is exactly that you’re working on.

If all things seem right but water still won’t come out of your hose after everything has been connected then go back into Step Five and make sure that there aren’t any leaks somewhere along the line or that none of your connections are too loose for their own good!

Bonus Step: Test Out Your Above Ground Pool Plumbing System

This is an important step so don’t forget about the whole reason why you set this up in the first place because now everyone can use their wonderful new above ground pool for as long as they want and not have any concerns whatsoever since everything should be working just fine after completing all of these steps!

If there are still leaks, then go back over every piece carefully before putting things together again; if everything seems good, however, congratulations on successfully setting up a plumbing system for an above-ground pool by yourself!

You’ve done it! Now enjoy your brand new above-ground pool without having to worry about how you’re going to get water into it or anything like that at all. You might also want to know how to add plumbing to the garage or knowing what IC is in plumbing. Just check our blog post or click the links.