Building a fence is an important project that can be difficult to do on your own, but with the help of this blog post, you will learn how to use a laser level to build a fence in 6 simple steps.

A laser level is a helpful tool to have when building a fence. It helps you get the measurements right, and it can also help you make sure that all of your posts are in line with each other. But how do you use one? Read more to know more!

How to Use a Laser Level to Build A Fence

The six steps below will show you how to build your fence with a laser level and provide you with some helpful tips.

Step 1: Determine the Length of Your Fence

You can do this by measuring your fence line or taking a guess at what length would look best for your yard. It is better to measure the line in most cases because exact measurements give more accurate results when using a laser level.

Step 2: Mark Off Your Fence Line with Spray Paint or Stakes

You can use spray paint to mark the line, but be sure that it will not become washed off in a rainstorm. If you plan on using stakes instead of paint, make sure they are tall enough, so your tape measure does not hit them when pulled out all the way for measuring.

Step 3: Attach the Laser Level onto a Tripod and Align It With Your Starting Point

The laser level should point straight up from where it is attached to ensure accuracy along its entire length.

Once this has been done attach your tripod at either end of your fence line ensuring that both legs have been placed into soil firmly by wiggling each leg until it is pushed into the soil as far as possible.

Step 4: Attach Your Tape Measure to the Laser Level and Align It with Your Starting Point

Using your tape measure, attach one end of it to the laser level near where you began lining off your fence line. Next, take that same side and pull out ten feet of tape before attaching it again on a new stake or spray paint spots on your fence line.

Step 5: Make Sure You Have Enough Rods for Each Side That Is Being Built

When using a traditional post hole digger, be sure you have enough rods because if not, this will cause problems when digging each individual hole. If there are any gaps in between the rods they should be placed approximately three inches apart.

Step 6: Start Digging Posts

This step is the simplest of them all, just start digging your holes where you placed paint or stakes. If using a traditional post hole digger, be sure it has been turned on its side so that instead of digging out the soil from under the ground, it will simply push dirt off to one side as it goes down deeper into the earth.

Once each individual hole has been dug, place your fence posts inside and begin filling up with concrete by following instructions listed on the package for how much water should be mixed in with powder prior to pouring into each hole.

Tips On How to Use a Laser Level

Be sure your laser level is at the same height from where it was attached to a tripod when starting a new side. Doing this will ensure that you have straight lines and even spacing between each post in case they are not all exactly ten feet apart from one another.

A helpful tip would be to purchase more rods for digging purposes if going through hard-packed or rocky soil, as these can make it harder to dig holes without them breaking inside of the hole before getting filled with concrete.

In some cases, people may need up to nine rods per hole which could add up quickly depending on how long your fence line actually ends up being once finished building it with a traditional post hole digger.

Make sure stakes or paint spots that you use to mark off your fence line can withstand heavy winds, rain, and any weather conditions, as this will ensure they do not become washed away or blow around. If using paint, be sure it is outdoor grade so it will last through the elements.

When digging holes with a traditional post-hole digger, make sure dirt is pushed to one side of each hole before beginning to fill up with concrete by following instructions listed on the package for how much water should be mixed in with powder prior to pouring into each individual hole.

Doing this ensures no gaps inside posts when finished building a fence, which could lead to weak spots along boundary lines if anything fell against them during a storm such as wind blowing over loose branches from trees after strong gusts hit or even heavy rain causing the soil to wash away.

Using a laser level is not difficult when building individual fence posts, yet it can be time-consuming if there are multiple areas that need them, such as having animals and wanting an electric line surrounding your property or crop area.

In this instance it may be better off for someone to purchase one instead of trying to use their own personal equipment which could end up costing more money than expected once buying new batteries every few hours depending on how often they must recharge before each post has been finished digging and filling with concrete.

The steps to follow when building a fence using laser levels are simple and easy to follow. It is best for one who has never done this before to go over each step slowly in order, so they are not confused when starting or putting finishing touches on their fence line project.

Suggested Post:

• How to Use a Double Ended Screw: 10 Essential Tips
• How to Use a Laser Level for Tiling: 7 Steps to Perfectly Tiled Floor