How to Change the Blade on a Ridgid Tile Saw: 6 Simple Steps

Share
How to Change the Blade on a Ridgid Tile Saw

Ridgid tile saws are a powerful tool that can be used for many different applications. Whether you’re doing remodeling work on your home, or simply looking to make some DIY repairs on the porch, a Ridgid tile saw is sure to come in handy.

One of the most common problems with any power tool is that they eventually need their blades changed out.

How to Change the Blade on a Ridgid Tile Saw

Here are the 6 steps on how to change the blade on a Ridgid tile saw:

Step 1: Unplug the Ridgid Tile Saw from its power source.

The first thing you need to do is to make sure you’ve unplugged the Ridgid tile saw from its power source. If it is plugged in, there’s a chance that you could get hurt when changing out the blades!

Step 2: Loosen the Screws

The second step is to loosen all of the screws on your Ridgid tile saw. After you’ve done that, then it’s time to remove each piece one by one- starting from either end and working toward the middle.

Step 3: Remove Blade Guard & Dust Shroud

Once you have loosened all of those screws, take a look at where they were attached to before removing them completely so that you can put them back in place correctly when changing the blade on the Ridgid tile saw! The third thing you need to do is simply remove the blade guard and dust shroud. It should come off fairly easily without any force needed to be involved with how to change the blade on the Ridgid tile saw. Simply grab onto the piece and pull it off.

Step 4: Remove Blade & Arbor Assembly

The fourth step is to remove the blade and arbor assembly. This will require you to use a wrench to get rid of everything that keeps your saw attached together! It should be very easy for you to do once you have already taken out all of those screws, so make sure not to skip this part when changing the blade on the Ridgid tile saw!

Once you’ve got the old blade removed, simply put on the new one- making sure that both sides are lined up correctly before tightening them by hand until they’re firmly set into place. You can then use some pliers or channel locks (wrench) if necessary in order to tighten down more if needed.

Step 5: Reassemble the Ridgid Tile Saw

Once you have put everything back together, it’s time to move on and reassemble your Ridgid tile saw! Start by putting blade guard and dust shroud back into place first, followed by tightening down any screws that might be leftover from step two. You should then test out how to change the blade on the Ridgid tile saw just in case anything comes loose as a result of moving around during transportation or heavy use.

Step 6: Put Blade & Arbor Assembly Back On Your Ridgid Tile Saw

The last thing you need to do is simply screw the blade and arbor assembly back onto your Ridgid tile saw where they belong using the wrench from step three. Once you have done that, then it’s time to plug your tile saw back in and start getting to work on whatever task was at hand!

Ridgid Tile Saw Maintenance

Even though changing the blade on the Ridgid tile saw is a relatively easy process. There are still some best practices for keeping your Ridgid tile saw going strong as long as possible through proper maintenance.

Make sure that the machine stays clean during operations by removing dust shroud whenever necessary. You should also make sure not to push down too hard when cutting with blades because pushing down harder than needed might cause damage over time or shorten out the life of your blade significantly faster than expected.

Be careful about what type of material you cut into next by checking the compatibility of your blade to the materials being used. Finally, make sure you know when it’s time for new blades in order to be prepared and avoid accidents like cutting into a blunt or broken piece by accident!

You should now know how to change the blade on the Ridgid tile saw thanks to these helpful steps in order to keep your machine working like new for years into the future! You can also check our blog post about flattening aluminum table saw tops and removing rust from a hand saw blade.

Share

0 Comments

Submit a Comment

Your email address will not be published. Required fields are marked *